Arofanatics Fish Talk Forums  

Go Back   Arofanatics Fish Talk Forums > Arowana Forum > Tank set-ups, Filtration & Water Management > Articles, Resources & FAQs

Reply
 
Thread Tools Display Modes
Old 04-10-2007, 04:34 PM   #11
atom
Guest
 
Posts: n/a
Default

Quote:
Originally Posted by bennkhoo View Post
Hi atom pls advise I'm using dymax denitrator should I turn on the powerhead or off it.Been running for few months seen it does not work at all.
For the time being, shut down the input for a few days but let the circulation pump on. Have you try feeding the denitrator unit?

Last edited by atom; 04-10-2007 at 04:41 PM.
  Reply With Quote
Old 04-10-2007, 04:52 PM   #12
bennkhoo
Arofanatic
 
Join Date: Jun 2006
Posts: 278
Default

Quote:
Originally Posted by atom View Post
For the time being, shut down the input for a few days but let the circulation pump on. Have you try feeding the denitrator unit?
Had follow your intruction before. Shut down the input for 2 days and check the nitrate it was zero.When I let the water drip 1 drop per second the nitrate went up.Shut down ok ,drip went up and regarding about feeding I do put 1ml.volka per day for 3 days. and stop test ok the next 2 days up again. Do you think I should add in deniball with the bioball.
bennkhoo is offline   Reply With Quote
Old 04-10-2007, 05:13 PM   #13
atom
Guest
 
Posts: n/a
Default

Quote:
Originally Posted by bennkhoo View Post
Had follow your intruction before. Shut down the input for 2 days and check the nitrate it was zero.When I let the water drip 1 drop per second the nitrate went up.Shut down ok ,drip went up and regarding about feeding I do put 1ml.volka per day for 3 days. and stop test ok the next 2 days up again. Do you think I should add in deniball with the bioball.
IMO, this is what has happened. Your dymax denitrator is a carbon base type. It requires organic carbon source for the denitrifying bacteria for respiration and growth. An example of such organic carbon is from the dissolved orgainc compound/carbon from the water column but the amount might be too small (very common) to play a crucial role. Another important factor is the presence of dissolved oxygen in the waters and its inhibiting effects. To effect denitrification, the oxygen concentration must be reduced to a level low enough to avoid inhibition or repression of nitrate reductase. Unless dissolved oxygen is removed by chemical addition, the amount of electron donor (organic carbon) added must be equal to that needed to remove the oxygen as well as the nitrate.

To cut the story short, the feeding must be constant n frequent. You can try injecting 0.5 ml of volka every 4 to 6 hourly basis. This can be done with a auto-setup using a timer and a dosing pump. This will be costly too. The easiest method is to use deniball. It is a slow dissolving organic plastic or shall I say ....time release organic carbon ball!

Last edited by atom; 04-10-2007 at 05:21 PM.
  Reply With Quote
Old 04-10-2007, 05:31 PM   #14
atom
Guest
 
Posts: n/a
Default

There are mainly 3 types of denitrator used by hobbyist.

1. Coil denitrator
2. Carbon based denitrator
3. Sulphur based denitrator
  Reply With Quote
Old 04-10-2007, 05:40 PM   #15
Spakase
Guest
 
Posts: n/a
Default

Great thread.
Can I ask a few questions:
1. Are bioballs better than rings or will any filter material, including sponge do?
2. Is there a necessity for some space in the Denitrator, ie not to fill up with material to the brim? What's the reason?
3. Heterotrophic bacteria - how did they get into the Denitrator? Besides heterotrophic bacteria, will there be other forms of bacteria present that are harmful to fishes?
4. All anaerobic bacteria in the Denitrator will die immediately upon exposure to oxygen - is this true? Can some survive and find it's way back into the tank?
5. Is it a good idea to feed the denitrator with aerobic bb?
6. Is it a good idea to fix a UV to the Denitrator's output to kill any bacteria exiting from the Denitrator, as an alternative, say if one wants to be certain none gets back to the tank?
7. Besides bacteria, what else can be found in the Denitrator's output?
8. Why is it important for the control valve to be located at the Denitrator's input?
9. What is known to kill anaerobic bacteria?n ie besides exposure to oxygen.
  Reply With Quote
Old 04-10-2007, 05:42 PM   #16
bennkhoo
Arofanatic
 
Join Date: Jun 2006
Posts: 278
Default

Quote:
Originally Posted by atom View Post
IMO, this is what has happened. Your dymax denitrator is a carbon base type. It requires organic carbon source for the denitrifying bacteria for respiration and growth. An example of such organic carbon is from the dissolved orgainc compound/carbon from the water column but the amount might be too small (very common) to play a crucial role. Another important factor is the presence of dissolved oxygen in the waters and its inhibiting effects. To effect denitrification, the oxygen concentration must be reduced to a level low enough to avoid inhibition or repression of nitrate reductase. Unless dissolved oxygen is removed by chemical addition, the amount of electron donor (organic carbon) added must be equal to that needed to remove the oxygen as well as the nitrate.

To cut the story short, the feeding must be constant n frequent. You can try injecting 0.5 ml of volka every 4 to 6 hourly basis. This can be done with a auto-setup using a timer and a dosing pump. This will be costly too. The easiest method is to use deniball. It is a slow dissolving organic plastic or shall I say ....time release organic carbon ball!
Tks atom I were get the deniball and mixed with bioball. How many deniball and bioball should I mixed very much appericate for your advise.
bennkhoo is offline   Reply With Quote
Old 04-10-2007, 06:43 PM   #17
atom
Guest
 
Posts: n/a
Default

[QUOTE=Spakase;5539873]Great thread. Thanks. I will try my best in answering your questions.
Can I ask a few questions:
1. Are bioballs better than rings or will any filter material, including sponge do?

The anaerobes we are cultivating are of biofilm type. Biofilm is the structural appearance of bacterial mass (biomass) on the surface of the reactor support matrix (biomedia). Ideally, the biofilm should be a consistent and uniform accumulation of bacterial solids that appear like a gelatinous and slime-like layer that can be put into contact with the water being treated for the removal of nitrate contamination. As such, media with tiny pores (ceramic ring, biohome, fine pores sponge...etc) are not suitable. Another alternative is Jap Mat or super large pores sponge.

2. Is there a necessity for some space in the Denitrator, ie not to fill up with material to the brim? What's the reason?

Not really. I do it mainly for faciltating easier closing of the reactor cover as the pump and piping system are located internally.

3. Heterotrophic bacteria - how did they get into the Denitrator? Besides heterotrophic bacteria, will there be other forms of bacteria present that are harmful to fishes?

The formation of the bacteria is the same as the aerobe species in nitrification. As long as the parameter is ideal (not for us but the bacteria itself), the bacteria will begin to cultivate.
There are basically 3 types of anaerobic bacteria.

- Obligate anaerobes will die when exposed to atmospheric levels of oxygen.

- Facultative anaerobes can use oxygen when it is present.

- Aerotolerant organisms can survive in the presence of oxygen, but they are anaerobic because they do not use oxygen as a terminal electron acceptor.

There many strains and some are not .....shall we call it "not so nice?". I will discuss about this later.


4. All anaerobic bacteria in the Denitrator will die immediately upon exposure to oxygen - is this true? Can some survive and find it's way back into the tank?

It depends on the level of oxygen and duration of exposure. Remember about the aerotolerant and facultative anaerobe? It will find its way to the tank if you allows it to be but it will not survive.

5. Is it a good idea to feed the denitrator with aerobic bb?

How shall I explain this? In carbon-based denitrator, aerobic bb is cultivated to reduce the DO level inside the reactor. It actually co-exist together with the anaerobic bacteria.

6. What is the output from the Denitrator? Is it a good idea to fix a UV to the Denitrator's output to kill any bacteria exiting from the Denitrator, as an alternative, say if one wants to be certain none gets back to the tank?

Denitrification requires a controlled environment to work which is the same nitrification. The difference is the working area for denitrification is very small as compare to nitrification. This means that the flowrate has to be relative to the size of the anaerobe community and denitrification process.

Yes. I would advocate some measures to treat the denitrator's output. UVC and ozoniser are some examples. This is to prevent undesirable "pathogen" of releasing to the tank. I will touch more on this area later.

7. Besides bacteria, what else can be found in the Denitrator's output?

Same question as in 4 and 6. There are presence of excess biological solids being discharged by the denitrator or fouling resulting from extraneous reactions including sulfate reduction to produce traces of hydrogen sulfide. Fouling in this case also is referred to as “biofouling.”

8. Why is it important for the control valve to be located at the Denitrator's input?

One main resultant component in denitrification is nitrogen gas but there are also others due to biofouling too. If the valve is located at the output to controll the flowrate, the reactor risk pressure build-up and will result in leaking.

9. What is known to kill anaerobic bacteria?

O2, O3, light, UVC, chlorine, hydorgen peroxide...etc. .

Whew!
  Reply With Quote
Old 04-10-2007, 06:43 PM   #18
atom
Guest
 
Posts: n/a
Default

Quote:
Originally Posted by bennkhoo View Post
Tks atom I were get the deniball and mixed with bioball. How many deniball and bioball should I mixed very much appericate for your advise.
IMO, 10 will be sufficient.
  Reply With Quote
Old 04-10-2007, 09:00 PM   #19
Spakase
Guest
 
Posts: n/a
Default

Overwhelming information and experience!
Quote:
In carbon-based denitrator, aerobic bb is cultivated to reduce the DO level inside the reactor. It actually co-exist together with the anaerobic bacteria
A little confused over this, thought aerobic bac will perish once it enters the reacter, never mind, can explain later in your own time. Thanks, those questions were on my mind so I just reel them off one by one......sorry it was lengthy.....it seems you have all the answers already. This definitely increases the confidence level of many seeking a Denitrator solution.
  Reply With Quote
Old 04-10-2007, 09:16 PM   #20
atom
Guest
 
Posts: n/a
Default

Quote:
Originally Posted by Spakase View Post
Overwhelming information and experience!
A little confused over this, thought aerobic bac will perish once it enters the reacter, never mind, can explain later in your own time. Thanks, those questions were on my mind so I just reel them off one by one......sorry it was lengthy.....it seems you have all the answers already. This definitely increases the confidence level of many seeking a Denitrator solution.
Your questions are very appropriate and good. There are some points that were missed out but as I proceed further, it will eventually come into light. I try to be as concise as possible but as a novice trying to write an essay for the very first time, it is quite taxing on my limited grey cells.
  Reply With Quote
Reply


Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +9. The time now is 04:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright © 2000-2008 Arofanatics.com (Since 30th August 2000)