Arofanatics Fish Talk Forums  

Go Back   Arofanatics Fish Talk Forums > General Aquatic Forums > AroReefers > Equipment/DIY discussion

Reply
 
Thread Tools Display Modes
Old 16-07-2011, 10:20 PM   #1
gryphon
Arofanatic
 
Join Date: Feb 2011
Posts: 431
Default External temperature probe for Haliea 150A

Can anyone advise how do I modify the Haliea 150A chiller to use an external temperature probe (thermostat)?
gryphon is offline   Reply With Quote
Old 21-07-2011, 12:30 AM   #2
gryphon
Arofanatic
 
Join Date: Feb 2011
Posts: 431
Default

All thanks to the help from the various bros, I have managed to modify my Haliea 150A chiller to use an external temperature probe. Just want to share with other bros who are interested in this DIY. The modification took me less that 20min.

The external temperature probe/sensor was purchased from Sim Lim Tower (NOT Sim Lim Square) B1. It is the shop near the escalator, just ask if they sell Fox temperature controllers.
Bros here have successfully used 2 similar models (same price), FN-200N's replacement temperature probe which has a long metal probe/sensor or a NTC based plastic temperature probe/sensor. I have bought the latter, picture as shown below.


First remove the front panel of the Haliea 150A chiller by pulling from the bottom of the panel.


Next use your fingers (both hands will be easier) to reach behind the display panel to locate 2 tabs and press them down and push out the front panel.




The 2 tabs which I am refering to are circled below.


You can see that there is a pair of wires (red and black) which is connected to the internal water tank's temperature probe/sensor. Disconnect the connector (circled below) and attach the external temperature probe/sensor to it (attach to the end that is connected to the display panel). To attach the external temperature probe/sensor to the connector, you can use soldering iron to solder the points together.
Note that for the NTC based plastic temperature probe/sensor, you need to connect the wire with white words to the red wire and the other plain black wire to the black wire.


You can calibrate your chiller to match your tank's temperature by pressing and hold the Up and Down arrows together. Maximium is +1.5Deg and -1.5Deg
gryphon is offline   Reply With Quote
Old 21-07-2011, 11:42 AM   #3
avex30
Guest
 
Posts: n/a
Default

good sharing bro
  Reply With Quote
Old 21-07-2011, 11:52 AM   #4
Navanod
Arofanatic
 
Join Date: Feb 2009
Posts: 346
Default

Good job bro! Might be worth a sticky?
Navanod is offline   Reply With Quote
Old 21-07-2011, 12:59 PM   #5
eviltrain
Guest
 
Posts: n/a
Default

for those who don't know or don't have soldering iron, can use this wire connecter (with screw).



just expose the wire and put into the connector accordingly to bro gryphon instructions will do.

Good job bro Gryphon
  Reply With Quote
Old 21-07-2011, 05:08 PM   #6
gryphon
Arofanatic
 
Join Date: Feb 2011
Posts: 431
Default

Thanks for all your help Alan
gryphon is offline   Reply With Quote
Old 21-07-2011, 07:27 PM   #7
eviltrain
Guest
 
Posts: n/a
Default

Quote:
Originally Posted by gryphon View Post
Thanks for all your help Alan
I never do anything lei. Hee hee.
  Reply With Quote
Old 22-07-2011, 11:33 AM   #8
gryphon
Arofanatic
 
Join Date: Feb 2011
Posts: 431
Default

Thanks to the bros who up my Rep points. Please indicate your nick in your comments, if not I do not know who to THANK for the Rep points
gryphon is offline   Reply With Quote
Old 22-07-2011, 04:14 PM   #9
rcw
Guest
 
Posts: n/a
Default

Quote:
Originally Posted by gryphon View Post
All thanks to the help from the various bros, I have managed to modify my Haliea 150A chiller to use an external temperature probe. Just want to share with other bros who are interested in this DIY. The modification took me less that 20min.

The external temperature probe/sensor was purchased from Sim Lim Tower (NOT Sim Lim Square) B1. It is the shop near the escalator, just ask if they sell Fox temperature controllers.
Bros here have successfully used 2 similar models (same price), FN-200N's replacement temperature probe which has a long metal probe/sensor or a NTC based plastic temperature probe/sensor. I have bought the latter, picture as shown below.


First remove the front panel of the Haliea 150A chiller by pulling from the bottom of the panel.


Next use your fingers (both hands will be easier) to reach behind the display panel to locate 2 tabs and press them down and push out the front panel.




The 2 tabs which I am refering to are circled below.


You can see that there is a pair of wires (red and black) which is connected to the internal water tank's temperature probe/sensor. Disconnect the connector (circled below) and attach the external temperature probe/sensor to it (attach to the end that is connected to the display panel). To attach the external temperature probe/sensor to the connector, you can use soldering iron to solder the points together.
Note that for the NTC based plastic temperature probe/sensor, you need to connect the wire with white words to the red wire and the other plain black wire to the black wire.


You can calibrate your chiller to match your tank's temperature by pressing and hold the Up and Down arrows together. Maximium is +1.5Deg and -1.5Deg
Wa, great job, thanks for sharing bro
  Reply With Quote
Old 25-07-2011, 02:56 PM   #10
bigbird126
Guest
 
Posts: n/a
Default

Nice sharing. What is the outcome of the modification , improvement on efficiency?

Mind to share further
  Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +9. The time now is 04:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright © 2000-2008 Arofanatics.com (Since 30th August 2000)