Arofanatics Fish Talk Forums  

Go Back   Arofanatics Fish Talk Forums > Arowana Forum > Tank set-ups, Filtration & Water Management

Reply
 
Thread Tools Display Modes
Old 09-09-2014, 06:19 PM   #261
weesy
New Member
 
weesy's Avatar
 
Join Date: Mar 2014
Posts: 40
Default

Anyone did for the back? If so how to hold it in place?
weesy is offline   Reply With Quote
Old 09-09-2014, 07:48 PM   #262
Vitor
Dragon
 
Join Date: Jun 2013
Posts: 1,079
Default

I did for my 522. using 4ft PP boards at bras bersah art friend, cheap and good.

1 whole pic is not able to cover fully and wont go in because of bracing at centre.

so i bought and cut the PP boards to slightly less 2 ft to fit into the height of the tank. total i bought 3 pcs all cut to 2ft less a bit for height(or above the water level)

measure the width , slightly less than 2 ft.
i will cut the outer layer only so to easy to bent on the inner layer.
bent already will be 2 ft less so u can insert into tank.

then put both left and right side. so will be a gap at centre.
then the centre cut the 3rd pp board to 4" longer than gap measured.
then fill the gap at the centre with 2" each side overlapping.

i use suction cups to hold. every corner.
8 cups on both sides. the center pc is held by the 2 side boards pressed.

so far no issue for the 7mths i used. and later thrown away.
better and not shiny so no reflection.
Vitor is offline   Reply With Quote
Old 09-09-2014, 07:50 PM   #263
Vitor
Dragon
 
Join Date: Jun 2013
Posts: 1,079
Default

Quote:
Originally Posted by Vitor View Post
I did for my 522. using 4ft PP boards at bras bersah art friend, cheap and good.

1 whole pic is not able to cover fully and wont go in because of bracing at centre.

so i bought and cut the PP boards to slightly less 2 ft to fit into the height of the tank. total i bought 3 pcs all cut to 2ft less a bit for height(or above the water level)

measure the width , slightly less than 2 ft.
i will cut the outer layer only so to easy to bent on the inner layer.
bent already will be 2 ft less so u can insert into tank.

then put both left and right side. so will be a gap at centre.
then the centre cut the 3rd pp board to 4" longer than gap measured.
then fill the gap at the centre with 2" each side overlapping.

i use suction cups to hold. every corner.
8 cups on both sides. the center pc is held by the 2 side boards pressed.

so far no issue for the 7mths i used. and later thrown away.
better and not shiny so no reflection.
sorry correction i use 8 suction cups on one side. 4 corners of each face.
so 16 suction cups. total.

hold use a screw driver heat up and melt thru. as long as ur suction cup eyelid can squeeze thru , its good.
Vitor is offline   Reply With Quote
Old 10-09-2014, 01:29 PM   #264
weesy
New Member
 
weesy's Avatar
 
Join Date: Mar 2014
Posts: 40
Default

Thanks for the reply. What suction cup you use? I try to find in LFS but unable to find 1 with the big nipple, if u know what I mean ;p
weesy is offline   Reply With Quote
Old 12-09-2014, 11:11 PM   #265
Vitor
Dragon
 
Join Date: Jun 2013
Posts: 1,079
Default

Use normal w air tube hose ones . squeeze thru holes on board....when u finish wtt. The suction cups can used for other means eg. Hold air tubes
Vitor is offline   Reply With Quote
Old 17-10-2014, 12:41 AM   #266
Flairtender
Dragon
 
Flairtender's Avatar
 
Join Date: Jul 2001
Posts: 1,141
Default

Good contribution from Vitor regarding the back PP boards .

Would like to touch on something ....

For the sucker best get those black colour can stick longer however costlier.

For punching holes thru the pp board for the sucker to go thru , can buy those small leather holes puncher in hardware shop which cost about $3 to $5 . Easy and swift saving the hassle to burn screwdriver to melt thru .
Flairtender is offline   Reply With Quote
Old 03-01-2017, 10:05 PM   #267
wingshya08
New Member
 
Join Date: Dec 2016
Posts: 1
Default

Hi Bro Flairtender, will appreciate if u could help me with the dimension for the acrylic base I plan to put into my 4x2x2 tank. Bottom or inside the tank no brace. Only top surrounding of the tank has glass at sides. (L) 5cm glass x (B)6.5 cm glass with 15cm glass at centre of tank at the top. Thank u
wingshya08 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 3 (0 members and 3 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +9. The time now is 05:57 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright © 2000-2008 Arofanatics.com (Since 30th August 2000)