Arofanatics Fish Talk Forums  

Go Back   Arofanatics Fish Talk Forums > General Aquatic Forums > AroReefers > Equipment/DIY discussion

Reply
 
Thread Tools Display Modes
Old 12-05-2011, 03:39 AM   #1
qngwn
Arofanatic
 
qngwn's Avatar
 
Join Date: Jan 2009
Posts: 70
Red face DIY Inline CO2 Diffuser

Hi all,

Just building on the idea og an inline CO2 diffuser, not reactor.
http://www.greenleafaquariums.com/co...-diffuser.html

I kind of DIY-ed something like that.. but of course not in the tank.
Perhaps you guys would like to take a look at the pictures. i rather not type thousands of words..

Basically i used:
acrylic tube of 2 inches - $0.50
air stone - $0.30
check valve - $1.50
leftover plastic tubing for CO2 of 10cm - Y618 sells $0.20 for 1m.
glue gun - silicon will do as well, as long as water does not come out

Total cost -estimated $2.50

although i know that using a CO2 atomizer will be much better, but would not know if this thing would work out.. so decided to spend 30cents instead of $3.

I placed this DIY part on the inline to my canister filter, similiar to that of the actual one in the link shown above, just that mine is external, and costs less than 1/10 of the other's price.

Turned on my solenoid, and watch the CO2 bubbles coming out from the airstone, going against the flow of the water, and getting sucked into the canister.

Assuming that the bubbles have to go through all the many layers of filter and rings in the canister, get stirred by the impeller and out together with the flow of the water into my rainbar, i must say that 95% of the CO2 were dissolved. of course with the occasional fine bubbles of CO2 coming out from my rainbars.

I suggest those who are interested to try this out, to use this only if your set up needs low bubble per sec counts as i doubt that alot of co2 would be dissolved by the time the water goes back into the tank.

of course, please comment and advise! my first DIY here though..
(maybe i'll pull the airstone out and change to an atomizer.. but lazy to unplug everything)

Pictures shown below.
qngwn is offline   Reply With Quote
Old 12-05-2011, 03:41 AM   #2
qngwn
Arofanatic
 
qngwn's Avatar
 
Join Date: Jan 2009
Posts: 70
Default



drilled a hole, just big enough to squeeze the plastic tubing through.



Very fine bubbles going into the canister.. iphone camera cant capture!

Last edited by qngwn; 12-05-2011 at 03:43 AM.
qngwn is offline   Reply With Quote
Old 07-09-2011, 01:45 PM   #3
sapiloncat80
Guest
 
Posts: n/a
Default

bro, u don't put any bioball to disolve the O2 from canister ?

will this efective ? cos I see some thread they always use bioball for it.
  Reply With Quote
Old 28-11-2011, 06:26 PM   #4
monster_88
Guest
 
Posts: n/a
Default

Good work, well this is what hobby is all about . Only thing I wonder is will the water flow be adversely affected by the big airstone obstruction in the piping? Is it possible to bubble through the "normal" airstone in the 1st place? (I had to use the 'special' fine ones that will actually diffuses the CO2 - alot more expensive, 2-3 bubbles per sec may not work with normal airstone I think). Also, beware of leakage over time.
Good work tho
  Reply With Quote
Old 28-11-2011, 07:14 PM   #5
Navanod
Arofanatic
 
Join Date: Feb 2009
Posts: 346
Default

Nice...but I think its a risky thing that may eventually leak?
Boyu sells an inline diffuser at $6...so not worth DIY'ing in my opinion

Navanod is offline   Reply With Quote
Old 27-01-2012, 05:05 PM   #6
shrimp88
Guest
 
Posts: n/a
Default

Better to DIY at the pipe nearer or close to inside e tank,in case it leak over time.
  Reply With Quote
Old 26-03-2013, 03:56 PM   #7
cooldeice
Guest
 
Posts: n/a
Default

I never really like the idea of getting the CO2 into the filter. Wont the CO2 give negative effect on the bacteria inside the filter? They are aerobic bacteria right?
Please correct me if I am wrong.
  Reply With Quote
Reply

Tags
co2, diffuser, diy, inline, reactor


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +9. The time now is 02:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright © 2000-2008 Arofanatics.com (Since 30th August 2000)