Arofanatics Fish Talk Forums

Arofanatics Fish Talk Forums (http://www.arofanatics.com/forums/index.php)
-   Equipment/DIY discussion (http://www.arofanatics.com/forums/forumdisplay.php?f=44)
-   -   External temperature probe for Haliea 150A (http://www.arofanatics.com/forums/showthread.php?t=470139)

gryphon 16-07-2011 10:20 PM

External temperature probe for Haliea 150A
 
Can anyone advise how do I modify the Haliea 150A chiller to use an external temperature probe (thermostat)?

gryphon 21-07-2011 12:30 AM

All thanks to the help from the various bros, I have managed to modify my Haliea 150A chiller to use an external temperature probe. Just want to share with other bros who are interested in this DIY. The modification took me less that 20min.

The external temperature probe/sensor was purchased from Sim Lim Tower (NOT Sim Lim Square) B1. It is the shop near the escalator, just ask if they sell Fox temperature controllers.
Bros here have successfully used 2 similar models (same price), FN-200N's replacement temperature probe which has a long metal probe/sensor or a NTC based plastic temperature probe/sensor. I have bought the latter, picture as shown below.
http://img36.imageshack.us/img36/9554/tempsensor.jpg

First remove the front panel of the Haliea 150A chiller by pulling from the bottom of the panel.
http://img535.imageshack.us/img535/8664/step1j.jpg

Next use your fingers (both hands will be easier) to reach behind the display panel to locate 2 tabs and press them down and push out the front panel.
http://img717.imageshack.us/img717/8126/step2im.jpg

http://img814.imageshack.us/img814/4791/step3c.jpg

The 2 tabs which I am refering to are circled below.
http://img607.imageshack.us/img607/817/step4r.jpg

You can see that there is a pair of wires (red and black) which is connected to the internal water tank's temperature probe/sensor. Disconnect the connector (circled below) and attach the external temperature probe/sensor to it (attach to the end that is connected to the display panel). To attach the external temperature probe/sensor to the connector, you can use soldering iron to solder the points together.
Note that for the NTC based plastic temperature probe/sensor, you need to connect the wire with white words to the red wire and the other plain black wire to the black wire.
http://img220.imageshack.us/img220/1707/step5n.jpg

You can calibrate your chiller to match your tank's temperature by pressing and hold the Up and Down arrows together. Maximium is +1.5Deg and -1.5Deg

avex30 21-07-2011 11:42 AM

good sharing bro

Navanod 21-07-2011 11:52 AM

Good job bro! Might be worth a sticky?

eviltrain 21-07-2011 12:59 PM

for those who don't know or don't have soldering iron, can use this wire connecter (with screw).

http://m2.sourcingmap.com/smapimg/en...tor-58806n.jpg

just expose the wire and put into the connector accordingly to bro gryphon instructions will do.

Good job bro Gryphon :D

gryphon 21-07-2011 05:08 PM

Thanks for all your help Alan

eviltrain 21-07-2011 07:27 PM

Quote:

Originally Posted by gryphon (Post 8560886)
Thanks for all your help Alan

I never do anything lei. Hee hee.

gryphon 22-07-2011 11:33 AM

Thanks to the bros who up my Rep points. Please indicate your nick in your comments, if not I do not know who to THANK for the Rep points

rcw 22-07-2011 04:14 PM

Quote:

Originally Posted by gryphon (Post 8559817)
All thanks to the help from the various bros, I have managed to modify my Haliea 150A chiller to use an external temperature probe. Just want to share with other bros who are interested in this DIY. The modification took me less that 20min.

The external temperature probe/sensor was purchased from Sim Lim Tower (NOT Sim Lim Square) B1. It is the shop near the escalator, just ask if they sell Fox temperature controllers.
Bros here have successfully used 2 similar models (same price), FN-200N's replacement temperature probe which has a long metal probe/sensor or a NTC based plastic temperature probe/sensor. I have bought the latter, picture as shown below.
http://img36.imageshack.us/img36/9554/tempsensor.jpg

First remove the front panel of the Haliea 150A chiller by pulling from the bottom of the panel.
http://img535.imageshack.us/img535/8664/step1j.jpg

Next use your fingers (both hands will be easier) to reach behind the display panel to locate 2 tabs and press them down and push out the front panel.
http://img717.imageshack.us/img717/8126/step2im.jpg

http://img814.imageshack.us/img814/4791/step3c.jpg

The 2 tabs which I am refering to are circled below.
http://img607.imageshack.us/img607/817/step4r.jpg

You can see that there is a pair of wires (red and black) which is connected to the internal water tank's temperature probe/sensor. Disconnect the connector (circled below) and attach the external temperature probe/sensor to it (attach to the end that is connected to the display panel). To attach the external temperature probe/sensor to the connector, you can use soldering iron to solder the points together.
Note that for the NTC based plastic temperature probe/sensor, you need to connect the wire with white words to the red wire and the other plain black wire to the black wire.
http://img220.imageshack.us/img220/1707/step5n.jpg

You can calibrate your chiller to match your tank's temperature by pressing and hold the Up and Down arrows together. Maximium is +1.5Deg and -1.5Deg

Wa, great job, thanks for sharing bro

bigbird126 25-07-2011 02:56 PM

Nice sharing. What is the outcome of the modification , improvement on efficiency?

Mind to share further :)


All times are GMT +9. The time now is 07:20 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright © 2000-2008 Arofanatics.com (Since 30th August 2000)